Refinishing · Daly City
Hardwood Refinishing and Repair in Daly City
Sanding, staining, and board repair for the original oak floors in Daly City, Westlake, and the older San Francisco border neighborhoods.
(650) 414-5793 — price my refinishBefore You Replace It, Find Out If It Can Be Saved
Hardwood refinishing and repair in Daly City saves a lot of homeowners a lot of money, and the houses here are full of candidates. Plenty of the original oak strip floors laid in the tract-built neighborhoods around this city have never been sanded, which means they still have a full wear layer and can be brought back to new for a fraction of replacement cost. Flooring Installation Daly City looks at the floor and tells you honestly which side of that line you are on. If the boards are sound and the damage is surface level, refinishing is the answer. If they have been sanded to the nails, water has delaminated the field, or too many boards are cupped past flattening, replacement is the honest recommendation. People call us for this after pulling up carpet and discovering wood underneath, after a pet or a leak leaves a section ruined, or simply because the finish has worn through in the traffic lanes.
What Refinishing Includes
Repair, sanding, stain, and finish coats are quoted separately so you can see exactly what you are paying for.
Wear-layer assessment
We check the thickness remaining above the tongue at a vent or a threshold to confirm the floor can take another sanding. This is the first thing we look at and it decides everything else.
Board repair and weaving
Damaged, split, or missing boards are cut out and replaced with matching stock, woven into the existing field with staggered end joints so the patch disappears once the floor is sanded and stained as one surface.
Face-nail and fastener correction
Proud nails and staples are set below the surface before sanding, because a single fastener left high will destroy a sanding belt and scar the floor.
Dust-contained drum and belt sanding
Coarse through fine grit passes with the sander connected to HEPA-filtered containment, which keeps the overwhelming majority of the dust out of your house rather than in it.
Edging and corner detail
Edgers and corner scrapers take the sanding right to the baseboard and into the corners, so there is no ring of old finish left around the perimeter of the room.
Screening and buffing between coats
The floor is buffed and vacuumed between finish coats, which removes raised grain and dust nibs and is the difference between a smooth floor and a gritty one.
Custom stain matching and sample panels
We apply stain samples directly on your floor in an inconspicuous area so you choose the color on your actual wood, under your actual light, instead of from a chip.
Water-based or oil-modified finish application
Multiple coats of a commercial-grade finish, chosen with you based on cure time, ambient odor, and how much amber tone you want. Water-based finishes cure faster and are usually the better choice in an occupied home.
Recoat and screen for floors not needing full sanding
Where the finish is worn but the wood is untouched, a screen-and-recoat restores the surface in a day at a fraction of the cost of a full sand.
Squeak correction before finishing
With the floor accessible, loose boards are re-secured into the subfloor and joists so the squeak does not survive the refinish.
Containment, ventilation, and protection
Doorways are sealed, HVAC returns are covered, and air movement is managed while the finish cures so dust and odor stay controlled.
Cure-time guidance and final walkthrough
We tell you exactly when you can walk on it, when to put furniture back, and when area rugs can go down, then inspect the finished floor with you in daylight.
How a Refinish Runs
- 01
Assessment and stain samples
We evaluate the wear layer, count the boards that need replacing, and check for movement and squeaks. If you are refinishing, we apply stain samples on the floor itself so the color decision is made on real wood. The estimate separates repair, sanding, stain, and finish coats.
- 02
Repair and sanding
Boards are replaced and fasteners set, then the floor is sanded through the grit sequence with containment running. Most single-room jobs sand in a day. A full downstairs takes two. The house is largely unusable during this stage, which is why we work in sequence and keep it short.
- 03
Stain, finish, and cure
Stain goes on and is allowed to dry, then finish coats are applied with buffing in between. You can usually walk on it in socks the next day, put furniture back after a few days, and lay rugs after roughly two weeks. We give you the exact schedule for the product used.
Why Hire Us for Refinishing
We will tell you when refinishing is the wrong call
A floor sanded down to the fasteners cannot be saved and we will not take the job pretending otherwise. Equally, we will talk you out of replacing a floor that only needs a screen and recoat, even though the replacement is the bigger invoice.
Dust containment on every pass
Sanding hardwood without HEPA containment coats an entire house in fine dust that gets into everything. Our equipment is connected the whole time, which is not universal in this trade.
Repairs are woven, not patched
Cutting a rectangle out and dropping in a square of new boards is visible forever. We stagger the joints into the surrounding field so once the floor is sanded and stained as one surface, you cannot find the repair.
On every refinish
- CSLB Licensed, Bonded & Insured (C-15)
- HEPA Dust-Contained Sanding
- Stain Samples Applied to Your Actual Floor
- Woven Board Repairs
- Free In-Home Assessment
- Written Workmanship Warranty
Find Out What Your Existing Floor Is Worth
If there is wood under your carpet or a tired oak floor in the living room, the assessment costs nothing and often saves several thousand dollars against replacement. We will check the wear layer, count the boards that need work, and tell you plainly whether this floor has another life in it. Stain samples go on your own wood before you commit to a color.
(650) 414-5793